[an error occurred while processing this directive] [an error occurred while processing this directive]
|
В ISE 4.1i (Tutorial) показано ,как в Shematic editor_e одиночные выходные сигналы обЪединять в шину (напр.q(0),q(1)... в q(7:0)).
A наоборот,размножить выходы (напр.дешифратора cs(7:0) на cs(0),cs(1)...,чтобы потом по разному использовать каждый,нигде не показано.
Все попытки это сделать заканчиваются ошибками синтеза...
WARNING:Portability:111 - Message file "SchematicEditor.msg" wasn't found.
ERROR:SchematicEditor - Destination branch of bustap at (1280 512, 1376 512) is
not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 640, 1376 640) is
not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 768, 1376 768) is
not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 912, 1376 912) is
not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 1024, 1376 1024)
is not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 1152, 1376 1152)
is not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 1264, 1376 1264)
is not part of the source branch of the bustap.
ERROR:SchematicEditor - Destination branch of bustap at (1280 1408, 1376 1408)
is not part of the source branch of the bustap.
ERROR:SchematicEditor - Net "cs(0)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(0)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(1)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(1)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(2)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(2)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(3)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(3)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(4)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(4)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(5)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(5)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(6)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(6)" is a bit bus member name, but there is no
corresponding bit bus.
ERROR:SchematicEditor - Net "cs(7)" needs to be connected to pins or IO Ports.
ERROR:SchematicEditor - Net "cs(7)" is a bit bus member name, but there is no
corresponding bit bus.
EXEWRAP detected a return code of '1' from program 'sch2vhdl'
Может это в ISE 4.1i вообще невозможно сделать?
Подскажите пожалуйста.
E-mail: 
info@telesys.ru
