|
|
может кто сможет помочь в настройке взаимодействия емулятора SAU510-USB CCStudio v 3.1.19.
Сначала ни коде композер, ни xdsprobe его не видели (выдавали
сообщение):
-----[Select the controller]-----------------------------------------
This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510usb.dll'.
This utility will operate on port address '0x0'.
An error occurred while hard opening the controller.
-----[An error has occurred and this utility has aborted]-----------
This error is generated by TI's USCIF driver.
The value is `-180' (0xffffff4c).
The title is: `SC_ERR_CTL_NO_TRG_POWER'.
The explanation is:
The controller has detected a target power loss.
The user may have failed to turn-on or connect its source.
-------------------------------------------------------------
Хотя на выводах JTAG напряжения пристствовали (тактовая соединена на
борде выв. 9 и выв.11 замкнуты)
Потом в файле c:\CCStudio_v3.1\cc\bin\BrdDat\ccBrd0.dat прописал полный путь до c:\CCStudio_v3.1\cc\bin\sm510usb.dll
это не помогло, тогда я обратил внимание, что файл
c:\CCStudio_v3.1\cc\bin\Board.cfg содержит только одну строчку:
;cfg-2.0
я переименовал файл sm510usb.cfg в Board.cfg после этого заработал xdsprobe и xdsreset.
Сейчас xdsprobe -iv выдает следующее:
+++++++++++++++++++++++++++++++++++++++++
-----[Select the controller]----------------------------------------
This utility has selected an XDS510 class product.
This utility will load the adapter 'sm510usb.dll'.
This utility will operate on port address '0x0'.
The emulator adapter is named 'C:\CCStudio_v3.1\cc\bin\sm510usb.dll'.
The emulator adapter is titled 'SM510USB block-mode adapter'.
The emulator adapter is version '3.3.0'.
The emulator adapter is uses 'Block-Mode'.
The controller has an insertion length of '16' (0x0010).
The controller has a revision number of '1' (0x0001).
The controller type is 'The venerable TBC (74ACT8990)'.
The local memory has a base address of '0' (0x000000).
The local memory has a word capacity of '262144' (0x040000).
-----[Perform the scan-path length test on the JTAG IR and DR]---------------
This scan-path test uses blocks of 512 32-bit words.
The test for the JTAG IR instruction scan-path length succeeded.
The JTAG IR instruction scan-path length is 8 bits.
The test for the JTAG DR bypass scan-path length succeeded.
The JTAG DR bypass scan-path length is 1 bits.
-----[Perform the scan-path integrity test on the JTAG IR]-------------------
This scan-path test uses blocks of 512 32-bit words.
Starting an Integrity Test using 0xFFFFFFFF.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
The JTAG IR integrity test has succeeded.
-----[Perform the scan-path integrity test on the JTAG DR]-------------------
This scan-path test uses blocks of 512 32-bit words.
Starting an Integrity Test using 0xFFFFFFFF.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
The JTAG DR integrity test has succeeded.
+++++++++++++++++++++++++++++++++++++++++
то есть, вроде все тесты проходят, но при запуске кодэ композера, при
попытке соединится с емулятором он выдает ошибку чтения памяти:
+++++++++++++++++++++++++++++++++++++++++
Trouble Reading Memory Block at 0x40 on Page 0 of Length 0x1:
Error 0x80000002/-1070
Fatal Error during: Memory,
An unknown error prevented the emulator from accessing the processor
in a timely fashion.
It is recommended to RESET EMULATOR. This will disconnect each
target from the emulator. The targets should then be power cycled
or hard reset followed by an emureset and reconnect to each target.
Sequence ID: 0
Error Code: -1070
Error Class: 0x80000002
+++++++++++++++++++++++++++++++++++++++++
Помогите уже 4 дня пытаюсь привести его в чувство.
|
|
