Отправлено Фароненавистник 21 июня 2004 г. 10:59

На вопрос с предыдущей страницы по ниос.
Файл readme.txt
Nios(R) II Development Kit v1.0 readme.txt
============================================================
This readme.txt file accompanies the Nios II Development
Kit v1.0 release.

============================================================
This file contains the following sections:

o Nios II Development Kit Overview
o Important Notes
o Example Design Notes
o Known problems/limitations
o Installation & Operating Requirements
- Windows: NT4.0, XP and Windows 2000

============================================================
Nios II Development Kit Overview

The 1.0 release is designed to work with Quartus(R) II 4.0 sp1
and later on: Windows NT 4.0, XP, Windows 2000

Modelsim versions supported:
5.7e OEM plus precompiled libraries for Quartus II 4.0 SP1
available at:
https://www.altera.com/support/software/download/service_packs/quartus/dnl-qii40sp1.jsp
5.8a (SE and PE) and above.

This readme.txt file for the Nios II Development Kit software
includes information on important features.

The Nios II Development Kit:
o Allows hardware engineers to develop Nios II processor
hardware systems targeting Stratix(R), Cyclone(TM) and
Stratix II devices using the Quartus II
and SOPC Builder development environments.
o Allows software engineers to develop and debug C/C++
and assembly-language programs using the Nios II
integrated development environment (IDE).

NOTE: MAX+plus II development environment does not support the
Nios II processor.

The Nios II Development Kit is a package of software that
includes several development tools and IP cores.
o The Nios II IDE is based on the open-source Eclipse IDE
framework. (http:/www.eclipse.org/)
o This product includes software developed by the
Jaxen Project. (http://jaxen.sourceforge.net)
Jaxen Copyright (C) 2000-2002 Bob McWhirter &
James Strachan. All rights reserved.
You do not need a license for these products if you will only
develop software for the Nios II processor.

============================================================
Important Notes

o IMPORTANT: Do not use spaces or any of the characters
\ / : * ? " < > | ! in any of your directories,
paths or names of peripherals.

o LICENSING: You can create, compile and generate time_limited
programming files for Nios II hardware systems without obtaining
a license file. You must obtain a license for the Nios II
processor core and the Quartus II software to generate
non-time-limited programming files and flash programming
files for new Nios II hardware systems. See the getting
started material included with the Nios II development kit.
You do not need a license if you will only develop software
using the Nios II IDE.

============================================================
Example Design Notes

If you are running an example design and you are asked for
you 9-digit number after the letters 'ASJ', and your Nios II
Development Board does not have a sticker with a 9-digit
number after the letters 'ASJ', please enter a unique
9-digit number when prompted. Ensure that
this number is unique to each Nios board connected to your
network to avoid network address conflicts.

Telnet Software Example:

In order to successfully run the telnet example, you must
perform the following telnet command after obtaining an IP
address.

telnet 30

Small Example Design:

The "small" example design does not contain the JTAG Debug
Module.
This means that communicating with the example using
Nios II IDE is not possible. if you try to run the
Hello_LED software example on the "small" hardware
example from within Nios II IDE, you will get the error
message:

There are no Nios II CPUs with debug modules available which
match the values specified. Please check that your PLD is
correctly configured, downloading a new SOF file if necessary.

To run Hello_LED on the "small" example design, you must
perform the following steps:

1.) Build Hello_LED in Nios II IDE. This places a memory
initialization file in the hardware example project
directory.

2.) In Quartus II, open the "small" example design for
which you built the software.

3.) Recompile the hardware design. This integrates the
newly created memory contents (program memory) into
the design's onchip memory.

4.) Download the design's SOF file to the FPGA using
the Quartus II Programmer.

The example should run successfully.

============================================================
Known problems/limitations in Nios II Development Kit, v1.0

Please see the errata.txt document in the documents folder.

============================================================
Installation & Operating Requirements - Windows
NT 4.0 sp 5, and 6, Windows 2000, and Windows XP supported
============================================================
System requirements for the Nios II Development Kit:
A full edition installation of the Quartus II software
version 4.0 sp1 (or later).

You must have administrative privileges on the computer
you are installing the Nios II Development Kit on.

See the Quartus II readme for Quartus II system requirements
and installation procedures.

============================================================
Installing the Nios II v1.0 Development Kit on Windows

To install the Nios II software:

1. Insert the Compact Disk into
your CD-ROM drive. The Nios II Setup program window
appears automatically.

2. Click the "Install Altera Nios II Development Kit" button.
The Setup program starts automatically and guides you
through the installation process.

or:

If the Setup program is not already running,
start it manually: Choose Run from the Start menu,
type the following command, and click OK:

:\launcher.exe

The Setup program installs the Nios II Development Kit
on your computer.
-----------------------------------------

Не устанавливал, ибо слаб в медицине. И лекарствий нет.
Не против выложить скачанное, но нужно место.

• я это тож уже выкачал...если кому надо...выкладывайте ;) — Faith Healer   (21.06.2004 12:32, пустое)