|
|
xdsprobe -i:
---[The scan-path lengths of TI DSP's and microcontrollers]-----
The JTAG IR register for a ARM7 or ARM9 device has 4 bits.
The JTAG IR register for a `classic' TI DSP device has 8 bits.
The JTAG IR register for a `IceMaker' TI DSP device has 38 bits.
The JTAG IR register for a C621x or C671x device has 46 bits.
The older TI DSP devices with `classic' emulation
include the C4x, C5x, C8x, C20x, C24x products.
The newer TI DSP devices with `classic' emulation
include the VC33, C54x, C620x and C670x products.
The TI DSP devices with `IceMaker' emulation
include the C27x, C28x, C55x and C64x products.
---[Perform the scan-path length test on the JTAG IR and DR]----
The test for the JTAG IR instruction scan-path length failed.
The many-ones then many-zeros tested length was -16368 bits.
The many-zeros then many-ones tested length was 9 bits.
The test for the JTAG DR bypass scan-path length failed.
The many-ones then many-zeros tested length was -16368 bits.
The many-zeros then many-ones tested length was 2 bits.
The scan-path appears to consist of exactly two devices.
If the scan-path consists of only TI DSP chips, TI ARM cores
and TI micro-controllers, or 8-bit long bypassed devices,
then the measured lengths indicate that either the
link-delay or scan-path has a configuration error.
---[Perform the scan-path integrity test on the JTAG IR]--------
This scan-path test uses blocks of 512 32-bit words.
Starting an Integrity Test using 0xFFFFFFFF.
Word 219: scanned out 0xFFFFFFFF and scanned in 0xFF7FFFFF.
Word 359: scanned out 0xFFFFFFFF and scanned in 0xFFFFFF7F.
Some of the 32-bit data values were corrupted - 0.4 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
Word 156: scanned out 0x01FC1F1D and scanned in 0x017C1F1D.
Some of the 32-bit data values were corrupted - 0.2 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
Word 333: scanned out 0x5533CCAA and scanned in 0x5533CC2A.
Some of the 32-bit data values were corrupted - 0.2 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
The JTAG IR integrity test has failed.
---[Perform the scan-path integrity test on the JTAG DR]--------
This scan-path test uses blocks of 512 32-bit words.
Starting an Integrity Test using 0xFFFFFFFF.
Word 130: scanned out 0xFFFFFFFF and scanned in 0xFFFFBFFF.
Word 375: scanned out 0xFFFFFFFF and scanned in 0xFFFFBFFF.
Some of the 32-bit data values were corrupted - 0.4 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x00000000.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0xFE03E0E2.
Word 99: scanned out 0xFE03E0E2 and scanned in 0xFE03A0E2.
Word 344: scanned out 0xFE03E0E2 and scanned in 0xFE03A0E2.
Some of the 32-bit data values were corrupted - 0.4 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0x01FC1F1D.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
Starting an Integrity Test using 0x5533CCAA.
Word 67: scanned out 0x5533CCAA and scanned in 0x1533CCAA.
Word 312: scanned out 0x5533CCAA and scanned in 0x1533CCAA.
Some of the 32-bit data values were corrupted - 0.4 percent.
Finished that Integrity Test.
Starting an Integrity Test using 0xAACC3355.
All of the 32-bit data values were scanned correctly.
Finished that Integrity Test.
The JTAG DR integrity test has failed.
TCK - 6.25 MHz
если Вы имеете в виду board.cfg, то там ничего не стоит
|
|
